Differences

This shows you the differences between two versions of the page.

--- en:dpi:dpi_options:dpi_divert_spec:start [2023/08/28 15:01] – edrudichgmailcom
+++ en:dpi:dpi_options:dpi_divert_spec:start [Unknown date] (current) – removed - external edit (Unknown date) 127.0.0.1
@@ Line 1: / Line 1: @@
-====== Traffic Mirroring to External Platforms ======
-{{indexmenu_n>19}}
-A part of the traffic can be mirror from the common channel and transmitted for analysis and processing to external platforms.
-{{ :dpi:dpi_components:platform:dpi_divert_spec:sent_traffic_to_vas.png?600 |}}
-===== TAP Interfaces Configuration =====
-  * TAP0 - is used for  traffic diversion
-  * TAP1 - server side port that receives traffic
-  * Tunnel is created between TAP0 and TAP1 to transmit traffic to an external platform
-  * mac learning is disabled on the TAP0 interface
-Run the following commands from the console:
-<code bash>
-ip tuntap add tap0 mode tap
-ip tuntap add tap1 mode tap
-ip link set dev tap0 up
-ip link set dev tap1 up
-ip link add br0 type tunnel
-ip link set tap0 master br0
-bridge link set dev tap0 learning off
-ip link set tap1 master br0
-ifconfig tap0 192.168.4.20 up
-ifconfig tap1 192.168.4.21 up
-ifconfig br0 up
-</code>
-<note warning>Warning: TAP interfaces must be started after server restart!</note>
-===== Traffic Diversion Configuration =====
-Set up traffic diversion (the variant with the named profile):
-<code bash>
-  fdpi_ctrl load profile --service 14 --profile.name radius_accounting  --profile.json '{ "typedev" : "tap","dev" : "tap0","udp" : [ 1813 ] }' --outformat=json
-  fdpi_ctrl load --service 14 --profile.name radius_accounting --ip 10.16.252.11
-</code>
-here "typedev" : "tap" - type of device foк traffic diversion (TAP)
-    "dev" : "tap0" - the name of the network interface to which traffic is diverted
-    "udp" : [ 1813 ] - protocol and port number of the diverted traffic
- An example of use can be found in the section [[en:dpi:dpi_components:radius:radius_config:start|Radius Configuration Example #2]]
-<html></div></html>
-===== Autorun Setup =====
-To configure the traffic diversion interfaces at system startup, you have to:
-  - Add to the file **/etc/rc.d/rc.local**: \\ <code bash> ip tuntap add tap0 mode tap
-ip tuntap add tap1 mode tap
-ip link set dev tap0 up
-ip link set dev tap1 up
-ip link add br0 type tunnel
-ip link set tap0 master br0
-bridge link set dev tap0 learning off
-ip link set tap1 master br0
-ifconfig tap0 192.168.4.20 up
-ifconfig tap1 192.168.4.21 up
-ifconfig br0 up </code>
-  - Add **rc.local** processing permission: <code bash> chmod +x /etc/rc.d/rc.local </code>
-  - Change the file **/usr/lib/systemd/system/rc-local.service**: \\ <code bash> [Unit]
-Description=/etc/rc.d/rc.local Compatibility
-Documentation=man:systemd-rc-local-generator(8)
-ConditionFileIsExecutable=/etc/rc.d/rc.local
-After=network.target network-online.target
-[Service]
-Type=forking
-ExecStart=/etc/rc.d/rc.local start
-TimeoutSec=0
-RemainAfterExit=yes
-GuessMainPID=no
-[Install]
-WantedBy=multi-user.target </code>
-  - Enable **rc.local**, so that it starts every time after reboot: \\ <code bash> systemctl enable rc-local </code>

Profile

Settings

Differences