Differences

This shows you the differences between two versions of the page.

--- en:dpi:dpi_components:platform:by_pass:start [2023/08/29 07:29] – edrudichgmailcom
+++ en:dpi:dpi_components:platform:by_pass:start [Unknown date] (current) – removed - external edit (Unknown date) 127.0.0.1
@@ Line 1: / Line 1: @@
-====== Bypass network card questions ======
-{{indexmenu_n>17}}
-**Why do we recommend to use SILICOM network cards?**\\
- Here are the reasons:
-  * these cards support bypass functionality;
-  * drivers' licenses for DNA & Libzero can be included into delivery package. These drivers allow to get the highest productivity. The cards with included drivers are marked by -SQ1 (for 10Gb card).
-**Does bypass work in SILICOM cards on power off?**
-  * Fiber optics bypass does work on power off. It was verified on card PE210G2BPI9-SR-SQ1 short range/fiber;
-  * The copper bypass does work with no power. It was verified on card [[http://www.silicom-usa.com/Networking_Bypass_Adapters/PEG6BPi6-Six_Port_Copper_Gigabit_Ethernet_PCI_Express_Bypass_Server_Adapter_Intel_based_58|PEG6BPi6]]).
-**Do SILICOM cards have manual bypass control?**\\
-Basically DPI controls bypass by itself.\\
-bpctl_util utility provides manual bypass control, if required:\\
-  * bpctl_util all get_bypass - get bypass status;
-  * bpctl_util all set_bypass on - activate bypass;
-  * bpctl_util all set_bypass off - disactivate bypass.
-**We have got second-hand card. bypass does not work. What can we do?**\\
-The problem is caused by configuring this card as a standard. It means bypass functionality is off.\\
-To diagnose:\\
-  bpctl_util all get_std_nic
-:00.0 dna0 standard
-:00.1 dna1 slave
-:00.2 dna2 standard
-:00.3 dna3 slave
-The correct result is: non-standard.\\ \\
-To set the card in bypass mode, one should execute the following instructions:\\
-  bpctl_util all set_std_nic off
-This instruction switches the card into non-standard mode: it means, with bypass mode.
-**Explanation of bypass switching time**\\ The bypass is activated in a short time interval of about 0.5 seconds (by default), but for reasons of interfaces overlapping it may take a longer time interval. Below is the manufacturer's explanation of bypass switching. \\
-Such duration of switching can affect BGP, OSPF and other mechanisms, due to a brief disconnection (duration may vary, see description below) or several disconnections as in case of server or service restart ( //service->break->bypass->break->service//). In this case the session recovery time (BGP, OSPF) depends on their settings and may last up to several tens of seconds. To reduce this interval you need to configure yourself to reduce the session recovery time after disconnection. **For example**, on Juniper equipment hold-timer down 500ms is configured to avoid BGP session breakup and routing tables rebuilding:
-<code>set interfaces <ifname> hold-time up 500 down 500</code>
-where 500 ms is the timeout before the interface's operational status changes
-  Basically, the time for the bypass mechanism to switch from one mode to another is 10mS.
-  The timing that you are seeing relates to re-establish the link and then re-establish
-  the connection (with new routing tables in switches and devices).
-  This switch to bypass mode is done in our product by physically connecting the pair of
-  the ports together (wire to wire). This means that when this happen our product is actually out
-  of the picture and the start of the traffic with this new connection will depend on
-  the two networking devices (router / switch / device) on how they link together and how
-  they establish the connection again. You can try to  force fix mode (not auto-neg,
-  change to force 1G FD or so) this might reduce the time needed for the negotiation.
-  Not sure how much.
-  For the change from bypass mode to normal mode - all the above also stand as well.
-  The networking devices (router / switch / device) loss the link with each other and
-  starts establish the connection with the Silicom NIC . Here you have more control as
-  the link is done between the two devices and your system (Check that all the devices
-  are set to the same speed settings)
-  From our customer and our experience a 1-3sec is a reasonable time to get the Copper 1G link
-  to be establish between 2 network devices.
-**However, one port on the NIC is in bypass mode and does not filter traffic.**\\
-If it is configured (in/out_dev), but does not switch, try resetting the bypass switch in the card to its initial state:
-  bpctl_util all set_bypass off
-  bpctl_util all set_dis_bypass off
-  bpctl_util all set_bypass_pwoff on
-  bpctl_util all set_bypass_pwup on
-  bpctl_util all set_std_nic off
-  bpctl_util all get_bypass_change on
-  bpctl_util all get_tx on
-  bpctl_util all get_tpl off
-  bpctl_util all get_wait_at_pwup off
-  bpctl_util all get_hw_reset off
-  bpctl_util all get_disc off
-  bpctl_util all get_disc_change off
-  bpctl_util all get_dis_disc off
-  bpctl_util all get_disc_pwup off
-  bpctl_util all get_wd_exp_mode bypass
-  bpctl_util all get_wd_autoreset disable
- If it doesn't work, it means the card is defective, replace it under warranty.
-**Setting up Juniper so that switching to and from bypass does not cause routes to be re-routed.**\\
- <code bash>set interfaces <ifname> hold-time up 500 down 500
-show xe-5/2/0
- description "-= 20G UPLINK LAGG =-";
-hold-time up 1000 down 1000;
-gigether-options {
-.3ad ae1;
-}</code>
-**Setting up Cisco so that switching to and from bypass does not cause routes to be re-routed.**\\
-  int fa0/0
-  ip bgp fast-external-fallover deny
- Note:
-  BGP Fast-external-fallover command terminates external BGP sessions of any directly adjacent peer if the link used to reach the peer goes down; without waiting for the hold-down timer to expire
-**List of all dna interfaces and their MAC addresses**\\
-grep ^ /sys/class/net/dna?/address
-**How to check if the card can perform bypass**\\
- You can check for bypass by running the command:
-  lspci -v|grep -A1 Eth
-For cards with bypass, the Subsystem field will indicate:
-  Subsystem: Silicom Ltd. Device

Profile

Settings

Differences

Differences

What were you trying to find?