| |
| en:dpi:bras_bng:bras_pppoe:pppoe_pppol2tp_parameters [2025/09/29 14:53] – created elena.krasnobryzh | en:dpi:bras_bng:bras_pppoe:pppoe_pppol2tp_parameters [2025/09/29 16:22] (current) – elena.krasnobryzh |
|---|
| {{indexmenu_n>2}} | {{indexmenu_n>2}} |
| ======Common parameters for PPPoE and PPPoL2TP====== | ======Common parameters for PPPoE and PPPoL2TP====== |
| | |
| | ^ Parameter ^ Description ^ Default Value and Possible Values ^ |
| | | ''bras_ppp_mru_max'' | Maximum size of a PPP packet wrapped in PPPoE. \\ **Change this parameter with caution!** | Default value is 1492. Can be increased [RFC 4638] if the Ethernet network MTU exceeds 1500. Calculated as: ''MTU - 6 (PPPoE header) - 2 (PPP Protocol ID)''. If VLAN/QinQ is present, their length is also subtracted. The parameter must be coordinated with ''snaplen'' | |
| | | ''bras_ppp_mac_auth'' | Flag enabling RADIUS authorization by MAC address. Used if PPP did not negotiate an authorization protocol. If MAC authorization is disabled and there is no authorization protocol, the PPP session is not established | ''0'' — MAC address authorization prohibited (default value)\\ ''1'' — MAC address authorization allowed | |
| | | ''bras_ppp_restart_timeout'' | Timeout for resending LCP cfg-req and term-req requests in seconds | Default value: 3 seconds [RFC1661] | |
| | | ''bras_ppp_ping_timeout'' | PPP session ping timeout in seconds.\\ Pinging is the sending of LCP Echo-Request when there are no packets from the client | ''0'' — do not use pinging\\ Default value: 60 seconds | |
| | | ''bras_ppp_max_terminate'' | Maximum number of attempts to send Terminate-Request without a confirming Terminate-Ack | Default value: 2 [RFC1661] | |
| | | ''bras_ppp_max_configure'' | Maximum number of attempts to send Configure-Request without receiving Cfg-Ack, Cfg-Nak, or Cfg-Reject | Default value: 10 [RFC1661] | |
| | | ''bras_ppp_max_failure'' | Maximum number of consecutive Configure-Nak messages. Upon reaching this threshold, it is considered that the parties cannot agree on connection parameters, and thereafter Cfg-Reject will be sent instead of Cfg-Nak.\\ This parameter also regulates the maximum number of unanswered echo requests: if there are no packets from the subscriber and no responses to the number of pings specified in the parameter, the session is closed due to subscriber inactivity | Default value: 5 [RFC1661] | |
| | | ''bras_ppp_idle_timeout'' | Control of PPPoE subscriber inactivity. \\ The inactivity interval (absence of packets from the subscriber) is set by the Radius attribute Idle-Timeout; if this attribute is not present in Access-Accept, this parameter is used. If there are no packets from the subscriber during the idle-timeout, a ping (LCP Echo Request) is sent to the subscriber at intervals of ''bras_ppp_ping_timeout'' seconds. If there is no response from the subscriber for ''bras_ppp_max_failure'' consecutive pings — the session is considered terminated due to subscriber inactivity | Default value: 300 seconds | |
| | | ''bras_pppoe_session'' | Maximum number of PPP sessions | | |
| | |
| | =====CLI Parameters===== |
| | ''ppp term'' — termination of all PPP sessions without distinguishing between PPPoE and L2TP tunnels. It is possible to specify parameters ''ip'', ''mac'', ''subs_id'', ''login'' or ''all'': |
| | <code bash>ppp term [hard] [ip=X | mac=X | subs_id=X | login=X | all]</code> |
| | |
| | The key for PPP sessions is composite: ''l2subs_id'' + ''tunnel-IP''. |
| | CLI commands that accept ''subs_id'' as a key (''subs prop show'', ''l2tp show session'', ''l2tp term'', etc.) may return multiple records with the same ''l2subs_id''. |
